Swirl & Shine

Gtechniq C5 vs CarPro CQuartz DLUX

Two bonded wheel coatings, two published heat figures, and two completely different application windows. One is a wheel coating that only does wheels. The other coats your faded trim with the same bottle - and makes you beat a clock that moves with the air temperature.

By Stephen V.Last updated How we rank

How this is funded: we earn a commission if you buy through our links, at no extra cost to you. It never changes which product we recommend, and we’ll always tell you who should skip one. Full disclosure.

If you have decided a wheel deserves a real bonded coating rather than a spray, these are the two bottles the decision usually comes down to. Both publish a heat figure, which almost nothing else in car care does. Both publish a coverage figure, which is rarer still. And both are genuine cure-and-stay coatings rather than a wax with “ceramic” on the label.

So the choice is not about which one is better. It is about two things their own pages make very clear: whether you also want to coat your faded black plastic, and how much of a timing game you are willing to play in a driveway. Everything below is the makers’ own published wording, read on their own sites and cited at the foot of the page. We have not applied either product to a test wheel, and nothing here is a result we produced.

The short answer

Buy Gtechniq C5 Wheel Armor if wheels are the only thing you are coating, you have a garage or a guaranteed dry night, and you want a fixed instruction you can follow the same way on every wheel.

Buy CarPro CQuartz DLUX if you want the wheels and the sun-faded trim done out of one bottle, you are coating more than one car, or your drying window is a few hours rather than overnight.

What each maker actually publishes

This is the comparison. Note that every row is filled on both sides — which is unusual enough in this category to be worth saying out loud, and the reason these two are the top of our wheel protection roundup rather than the cheaper bottles beside them.

Published claimGtechniq C5 Wheel ArmorCarPro CQuartz DLUX
SurfacesAlloy rims and brake calipersPlastic, rubber, metal and various wheel finishes
Heat claimRetains integrity up to 600°C (1112°F)Withstands temperatures up to 1000°F
DurabilityUp to 2 years, up to 18 months, or around 12 months — three figures across the maker’s own pagesUp to two years or more
Coverage15 ml = outer rim faces up to 17 in; 30 ml = inner and outer faces up to 20 inApproximately 10 ml per vehicle
PrepWheel cleaner, iron remover, then Panel Wipe on the dry wheelWash, IronX, polish if needed, then CarPro Eraser wipe-down
Wipe-off windowBuff residue within 30–60 seconds, half a wheel at a time1 minute at 90°F up to 8 minutes at 50°F; matte flashes 1 minute at 90°F
Cure12 hours indoors before weather1–3 hours no water; no washing for 3 days
Finishes ruled outPolished metalsNone named, but never polish a matte surface, and a caution against coating any finish you cannot correct
Shelf life3 months opened, 12 months unopenedInstall within 12 months of purchase
WarrantyNot publishedNot published

The heat figures, read properly

This is the only place in the comparison where a buyer can be actively misled by the marketing, so it is worth doing the arithmetic. CarPro publishes 1000°F. Gtechniq publishes 600°C, which the brand itself converts to 1112°F. The smaller-looking number is the higher one.

Having said that, we would not buy either coating on those 112 degrees. Both figures are the maker’s own, neither is a test result we can inspect, and both are far beyond anything a wheel face reaches in normal driving — the rotor runs hot, the rim face runs much cooler than the rotor. What the heat claim really tells you is that the product was formulated for a surface with a brake behind it rather than for a painted panel. That is the signal. The exact digits are not.

For contrast: Chemical Guys’ own wheel sealant says it is “Designed to withstand high heat braking conditions” and attaches no temperature to that sentence at all. Two makers publishing a number, in a category where the norm is a heat adjective with nothing behind it, is why this comparison is between these two bottles.

The real difference: one surface or two

Strip away the specs and DLUX is a trim and wheel coating while C5 is a wheel coating. If the black plastic around your bumpers and mirror housings has gone gray, DLUX does both jobs out of one bottle, and the 30 ml size with a published 10 ml per vehicle means there is genuinely enough in there to do it. That dual use is why detailers keep DLUX on the shelf even when they own something else for wheels, and it is the single strongest reason to pick it here.

If your trim is fine, that capability is money you are not using. And trim is a decision with its own answer: our Cerakote Trim Coat vs Solution Finish comparison covers the two products sold specifically for faded plastic, one of which publishes a guaranteed wash count. Coat the wheels with C5 and the trim with a trim product, and you have two products that each do one job properly.

The application difference, which is bigger than it looks

Gtechniq asks you to work in halves

The published C5 method is unusually prescriptive and that is a feature. Load the applicator with a few drops, spread across no more than half a wheel at a time, then buff the residue off with a microfiber cloth within 30 to 60 seconds. Gloves on. Clean, dry wheel, wiped with Panel Wipe first. Those instructions do not change with the weather, so you can rehearse them on the back of one wheel and then repeat the same motion seven more times.

The cost is the cure: 12 hours indoors before the wheels see weather. On a driveway in November that is not a small ask, and it is the reason we would only recommend C5 to someone with a garage or a forecast they trust.

CarPro asks you to read a thermometer

DLUX publishes its wipe-off as a range rather than a number: “let cure 1 minute at 90F up to 8 minutes at 50F” on painted or chrome wheels. That is genuinely more honest than a single figure — coatings really do flash faster in heat — but it moves the judgment onto you. Wipe too early and you drag the coating off; wipe too late and you are polishing out high spots on a surface you just coated. Matte wheels get a separate published instruction (flash 1 minute at 90°F) and no published figure for cooler air at all.

What DLUX gives back is a shorter wait afterwards: 1 to 3 hours with no water, a 24-hour rule about wiping water off before it dries, and no washing for 3 days. If you can only get a few dry hours, that is the coating that fits.

Prep: the step that decides whether either works

Both makers publish a prep sequence, and both sequences end with a solvent wipe using their own product — Panel Wipe for Gtechniq, Eraser for CarPro. Before that, both want the embedded iron off the wheel: Gtechniq’s wheel FAQ says a dedicated wheel cleaner then an iron remover, CarPro names IronX directly.

That matters more on a wheel than anywhere else on the car, because brake dust is embedded metal rather than surface dirt. A coating applied over it bonds to the contamination, and when the contamination lifts, the coating goes with it. If you are going to skip something, skip the coating and keep the iron remover — not the other way round. A small exterior detailing brush earns its keep here too: lug recesses and spoke roots are exactly where cleaner sits unagitated and where a coating then fails first.

Honest limitations on both

Neither maker publishes a warranty. Both durability claims are marketing figures rather than guarantees, and one of the two brands cannot keep its own figure consistent across three of its own pages. Neither publishes a hardness figure or a contact angle for the wheel application. Neither tells you what happens at year three.

And both have a shelf life you should take seriously: three months once opened for C5, twelve months from purchase for DLUX. Neither of these is a bottle you buy now and use next spring, which in practice means buying the size that matches the job in front of you rather than the size that looks like better value per milliliter.

So which one should you buy?

Wheels only, with a garage: Gtechniq C5. The published heat figure is the higher of the two once you convert it, the method is fixed rather than weather-dependent, and the coverage note tells you exactly which bottle size does the job you have in mind — just read it before you add the 15 ml to the cart, because outer faces only is not the same as coating the barrels.

Wheels plus faded trim, or more than one car, or a short dry window: CarPro CQuartz DLUX. One bottle, two surfaces, a published 10 ml per vehicle, and a cure measured in hours rather than overnight. Accept that you are taking on a timed wipe-off that changes with the temperature, and do the first wheel in the shade with a clock running.

Either way, the thing that decides the outcome is not the bottle. It is whether the wheel is actually clean, actually decontaminated and actually dry when the coating goes on. Both makers say so in their own published sequences, and both are right.

Frequently asked questions

Which lasts longer, Gtechniq C5 or CarPro DLUX?

On published figures, DLUX - but only because its maker publishes one number and Gtechniq publishes three. CarPro states DLUX protects "for up to two years or more" and says it consistently. Gtechniq's own pages give up to two years on the C5 product page, up to 18 months on its Wheel Coating Kit page, and around 12 months in its own wheel-cleaning article. Three figures from one brand for one bottle is not a range the maker meant to publish, so we plan around the lowest of them. Neither figure is a tested result and neither is a warranty.

Is 1000F better than 600C?

Those are closer than the digits suggest, and that is the point. 600C is 1112F, so Gtechniq's published figure is actually the higher of the two - by about 112F. CarPro's 1000F reads bigger on a listing because it is a bigger number in a different unit. Do not let the unit pick your coating: both products publish a heat claim far beyond anything a painted panel sees, which is more than almost any other product on this shelf can say, and the practical difference between them is not the heat figure.

Can I use CarPro DLUX on plastic trim as well as wheels?

Yes - that is the reason it exists. CarPro publishes it for "plastic, rubber, metal, and various wheel finishes", and detailers buy it for faded black trim as much as for rims. The prep on plastic is its own step: wipe the surface with CarPro Eraser, wipe dry, then "allow plastic to evaporate 20 minutes before applying". CarPro also warns in writing that on brand-new textured plastic you "use DLUX ceramic coatings at your own risk". Gtechniq C5 is a wheel product and we would not use it as a trim coating on the strength of its own page.

How much does each bottle cover?

Both makers publish a coverage figure, which is rare and genuinely useful. CarPro says "Approximately 10ml provides complete coverage for one vehicle", so a 30 ml bottle is roughly three cars' worth of wheels. Gtechniq publishes it by bottle size instead: the 15 ml covers outer rim faces on wheels up to 17 inches, and the 30 ml covers inner and outer faces on wheels up to 20 inches. Read that carefully before you buy the small Gtechniq bottle - outer faces only is a different job from coating the barrels.

Which one is harder to apply?

DLUX, because its clock moves. CarPro publishes the wipe-off window as a temperature range: "let cure 1 minute at 90F up to 8 minutes at 50F" on painted or chrome wheels, with a separate 1-minute flash published for matte at 90F and no figure at all for matte in cooler air. Gtechniq publishes a fixed instruction instead - spread no more than half a wheel at a time and buff off the residue within 30 to 60 seconds - which is a shorter window but the same window every time. A fixed 60 seconds is easier to work to than a window you have to infer from a thermometer.

Do I need the maker's own prep products?

Effectively yes for both, and that is a real cost. Gtechniq's published sequence is a dedicated wheel cleaner, then an iron remover, then its own Panel Wipe on the dry wheel. CarPro's is a wash, IronX decontamination, polishing if needed (never on matte), then a wipe-down with CarPro Eraser. Both are solvent wipes doing the same job - removing oils and polishing residue so the coating bonds to the wheel rather than to whatever is on it. Skipping that step is the single most common reason a coating fails early.

Can either one go on matte or polished wheels?

Matte, yes for both, with care. Gtechniq lists C5 as suitable for gloss, satin and matte rims and for chrome - but states plainly that it is not for polished metals. CarPro covers matte with a different flash step and prints two warnings worth reading twice: "NEVER polish a matte surface", and advice against putting any semi-permanent coating on a finish you cannot correct. If your wheels are polished aluminum, C5 is ruled out by its own maker and DLUX comes with a caution attached.

What happens if it rains that night?

This is where the two part company for a driveway job. Gtechniq publishes a 12-hour indoor cure before the wheels see weather, which means a garage or a dry 12 hours you can guarantee. CarPro publishes 1 to 3 hours with no water introduced to the surface, then a softer rule for the first 24 hours - "If wet during first 24 hours wipe off water before it dries on surface as a precaution" - and no washing for 3 days. If you have no garage and a changeable forecast, DLUX asks less of your weather window.

How long do these bottles keep once opened?

Both makers publish a shelf life, and both are shorter than people expect. Gtechniq says use C5 within 3 months of opening and 12 months unopened. CarPro says DLUX "should be installed within 12 months of purchase". That is a genuine argument for the smaller bottle if you own one car: a part-used coating is not a product you can store for next season, and a 30 ml bottle bought for one set of wheels is mostly a bottle you will throw away.

Sources

  • Gtechniq — C5 Wheel Armour — The only published temperature figure in the wheel-protection category, and a brand contradicting itself on durability. Heat: C5 "will retain its integrity up to temperatures of 600°C (1112°F)". Durability: the product page says protection for up to two years, the Wheel Coating Kit page says up to 18 months on the wheel face and inner barrel with proper care, and Gtechniq's own "How to clean your wheels properly" article says one application lasts around 12 months — three figures, all the maker's own. Method published: start with clean, dry wheels, wipe each wheel with Panel Wipe before coating for the best bond (the wheel FAQ adds a dedicated wheel cleaner then an iron remover first), shake the bottle, wear gloves, load the AP1 applicator with a few drops, spread across no more than half a wheel at a time, buff off the residue within 30 to 60 seconds with an MF1 cloth. Coverage: the 15 ml covers outer rim faces on wheels up to 17 inches, the 30 ml covers inner and outer faces on wheels up to 20 inches. Cure: keep the wheels indoors for 12 hours before exposing them to the elements. Finishes: suitable for gloss, satin and matte rims and for chrome, but not polished metals. Shelf life: use within 3 months of opening, 12 months unopened. No warranty term is published. Cited to Gtechniq's own UK site because gtechniq.com returns 403 to automated reads; the claims are the same brand's (accessed October 25, 2026)
  • CarPro — CQUARTZ DLUX Trim & Wheel Coating 30ml — The highest published heat claim of the four wheel products and the most method-dependent application. Published: protection "protecting your vehicle's trim and wheels for up to two years or more"; "Withstanding temperatures up to 1000°F"; surfaces "including plastic, rubber, metal, and various wheel finishes"; coverage of "Approximately 10ml provides complete coverage for one vehicle". Wipe-off windows are published as temperature ranges rather than single numbers — on painted or chrome wheels "let cure 1 minute at 90F up to 8 minutes at 50F" then wipe off in a circular motion, while matte wheels "Let flash 1minute at 90F" with no figure given for lower temperatures. Prep on plastic is "Wipe surface with CARPRO Eraser, wipe dry, and then allow plastic to evaporate 20 minutes before applying"; wheels are washed, decontaminated with IronX, polished as needed (never on matte) and wiped with Eraser. Post-application: "Allow the CARPRO DLUX coating to cure 1-3 hours without water being introduced to surface", "If wet during first 24 hours wipe off water before it dries on surface as a precaution", and "After 3 days you are free to wash as needed". Cautions the maker prints itself: on brand-new textured plastic, "use DLUX ceramic coatings at your own risk"; and "NEVER polish a matte surface", with advice against any semi-permanent coating on a finish you cannot polish. Shelf life "should be installed within 12 months of purchase". No warranty is published (accessed October 25, 2026)
  • Chemical Guys — Wheel Guard Max Coat Wheel and Rim Sealant (WAC_303) — The same brand's sealant, cited here for the contrast with its own wax: this page publishes a figure where the wax page publishes none. Published claims: it "lasts up to 8 full months of protection with just one application", it reduces "brake dust contamination by up to 75%", and it is "Designed to withstand high heat braking conditions" — wording with no temperature number attached. Applicable Finishes are again "Stainless Steel, Metal, Aluminum". No chemistry is named, no sizes, no coverage figure, no application directions (the "How to Use" heading has no content beneath it), no cure or buff time and no warranty are published. The page carries a California Proposition 65 warning stating the product "can expose you to chemicals including Diethanolamine" (accessed October 25, 2026)

Keep reading